++ Not Homologated for Switzerland ++
FUTECHER is the new brand from Minimotors enlarging the range of products of SPEEDWAY and DUALTRON. The FUTECHER GUN is a very eloborate product at a very affordable price. Equipped with a 600 Watt Motor and a strong 48V / 15,6 Ah battery, the maximum speed is 45 Km/h and the maximum range at about 65 Km. It has 8 inch inflatable tire at the front, a full tire at the back, front and rear suspension, front and rear drum brakes, and an integrated LED in the foot platform.
From CHF 879.00
FUTECHER is the brand new brand of the Minimotors Group after Dualtron and Speedway. The electric scooter FUTECHER GUN is a significantly improved version of the old Speedways with more range and a more modern design.
The FUTECHER GUN immediately stands out from the competition thanks to its LED system integrated in the steering column and on the sides of the deck. Obviously a resumption of models from the Dualtron range. It has a rear engine of 600 watts and a 48 V / 15.6 Ah battery that allows it to reach a top speed of 45 km / h and a maximum range of 65 km (value tested with a driver of 75 kg, on a flat stretch with an outside temperature of 20 ° C and a speed of 25 km / h). A very good performance at this price.
The EU Version with 45 Km/h top speed is also available but is not homologated for Switzerland.
For good driving experience, the scooter has a front and rear suspension system and an inflatable 8-inch tire at the front. The 8-inch rear tire is solid rubber to prevent punctures. The height of the handlebar is 131 cm above the ground. Front and rear lights are on the bottom of the footboard.
The net weight of the FUTECHER GUN electric scooter is 19 kg. Load weight of the scooter should not exceed 110 kg.
The complete operating manual for the FUTECHER GUN is supplied with the electric scooter.
The electric scooter is delivered assembled in its box. Only one manipulation is to tighten the screws on the brake levers and the display. The scope of delivery includes a tool kit that can be used to carry out this process. Remember to charge the FUTECHER GUN electric scooter 100% before your first ride.
The eScooter is supplied with a charger, a tool kit, the remote control for the LED system and the operating instructions.
To fold the scooter, all you have to do is press the latch at the base of the steering column and lower the handlebars until the latch clicks into place. You can then unfold the scooter by pressing the same latch. Use the tension lock to adjust the handlebar height. Fold out the handlebars and close the lock completely. Be sure to tighten the lock firmly to avoid vibration while driving.
The handles can also be folded. All you have to do is pull out the locking sleeves and flip down the handles. They're a little tough at first but get easier to close over time.
How to start the electric scooter:
To switch on the electric scooter FUTECHER GUN, you have to press the "Power" button for 3 seconds. The display will light up immediately.
Driving speed, battery level, mileage and speed are shown on the display. Depending on the speed that you select by pressing the white circle, the electric scooter has different types of acceleration. However, it's more fun to put in a high gear and then adjust the speed with the throttle while driving. To switch off the electric scooter, press and hold the "Power" button for three seconds. With the "Mode" button you can change the display from mileage to odometer or to the battery voltage.
If you hold down the "Mode" button for three seconds, you will enter the submenu of the electric scooter: P0 corresponds to the size of the wheel. For the FUTECHER GUN, choose number 8 for 8 inches.
P1 corresponds to the voltage of the controller. On the FUTECHER GUN there is a 48 volt controller.
P2 is the number 20.
P3 must stay at 0 With
P4 you can switch from kilometers to miles.
P5 is the start security. If you select 0, the scooter starts as soon as you operate the throttle. If you choose 1, you will need to physically propel the scooter before accelerating. The idea is to avoid accidentally starting the electric scooter.
P6 corresponds to "Tempomat". If you drive at a constant speed for 5 seconds, the scooter will stop at that speed until you apply the brakes. It is recommended to disable this feature.
P7 is the start acceleration type. You can adjust the engine power when accelerating. The higher the number (between 0 and 5), the smoother the acceleration.
With P8 you can limit the motor output. By selecting 5, you are limiting the speed of the scooter very significantly.
P9 is the battery saving mode. The higher the number, the more gently the scooter accelerates and limits the top speed.
PA stands for EBS or electronic brake. In mode 0 you have no electronic braking.
With Pb you can adjust the brightness of the LCD screen of the display.
PC is the time in minutes from which the FUTECHER GUN electric scooter goes into sleep mode.
With Pd you can activate or deactivate ABS.
In order to extend the service life of a lithium-ion battery, it is strongly recommended to keep the charge level of the battery between about 70% and 100%. Do not charge the battery when it is full (do not leave it to charge overnight), and never discharge the battery completely. When you charge your scooter, be sure to connect the charger to the power supply before connecting the electric scooter.
If you store the electric scooter for several months, it is important not to fully charge the battery, but to store the electric scooter with a charge level of approx. 60%.
Always store the electric scooter in a place protected from moisture and at a temperature of at least 5 ° C.
General maintenance of the electric scooter: It is important to check the tightness of the screws and the brakes very regularly, but at least once a month, as a scooter is exposed to a lot of vibrations while driving. Also remember to check the tire pressure regularly. With this model, it is advisable to inflate the front tire to a pressure of 3.5 bar (50 PSI).
Your electric scooter is cleaned with a damp sponge. Please note that this model is not waterproof. Do not use water or cleaning fluids for maintenance.
Below is a list of important accessories:
Masterlock CUFFS has a fastening system that can be attached to the steering column of your eScooter. A safe way to lock your scooter.
High-intensity front light for electric scooters. Aluminum with an intensity of 1200 lumens, waterproof, 6 lighting modes and an autonomy of approx. 6 hours when charged in high-intensity mode.
A helmet is not compulsory in Switzerland, but it is strongly recommended. The SMART4U helmet is equipped with an LED light on the back.